Network Working Group E. Allman Request for Comments: 5617 Sendmail, Inc. Category: Standards Track J. Fenton Cisco Systems, Inc. M. Delany Yahoo! Inc. J. Levine Taughannock Networks August 2009 DomainKeys Identified Mail (DKIM) Author Domain Signing Practices (ADSP) Abstract DomainKeys Identified Mail (DKIM) defines a domain-level authentication framework for email to permit verification of the source and contents of messages. This document specifies an adjunct mechanism to aid in assessing messages that do not contain a DKIM signature for the domain used in the author's address. It defines a record that can advertise whether a domain signs its outgoing mail as well as how other hosts can access that record. Status of This Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Copyright Notice Copyright (c) 2009 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents in effect on the date of publication of this document (http://trustee.ietf.org/license-info). Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Allman, et al. Standards Track [Page 1] RFC 5617 ADSP August 2009 Table of Contents 1. Introduction ....................................................3 2. Language and Terminology ........................................3 2.1. Terms Imported from the DKIM Signatures Specification ......3 2.2. Valid Signature ............................................4 2.3. Author Address .............................................4 2.4. Author Domain ..............................................4 2.5. Alleged Author .............................................4 2.6. Author Domain Signing Practices ............................4 2.7. Author Domain Signature ....................................4 3. Operation Overview ..............................................5 3.1. ADSP Applicability .........................................5 3.2. ADSP Usage .................................................6 3.3. ADSP Results ...............................................6 4. Detailed Description ............................................7 4.1. DNS Representation .........................................7 4.2. Publication of ADSP Records ................................7 4.2.1. Record Syntax .......................................7 4.3. ADSP Lookup Procedure ......................................9 5. IANA Considerations ............................................10 5.1. ADSP Specification Tag Registry ...........................10 5.2. ADSP Outbound Signing Practices Registry ..................11 5.3. Authentication-Results Method Registry Update .............11 5.4. Authentication-Results Result Registry Update .............11 6. Security Considerations ........................................13 6.1. ADSP Threat Model .........................................14 6.2. DNS Considerations ........................................14 6.3. DNS Wildcards .............................................15 6.4. Inappropriate Application of Author Domain Signatures .....15 7. References .....................................................16 7.1. Normative References ......................................16 7.2. Informative References ....................................16 Appendix A. Lookup Examples ......................................17 A.1. Domain and ADSP Exist .....................................17 A.2. Domain Exists, ADSP Does Not Exist ........................17 A.3. Domain Does Not Exist .....................................17 Appendix B. Usage Examples .......................................18 B.1. Single Location Domains ...................................18 B.2. Bulk Mailing Domains ......................................18 B.3. Bulk Mailing Domains with Discardable Mail ................19 B.4. Third-Party Senders .....................................19 B.5. Domains with Independent Users and Liberal Use Policies ...19 B.6. Non-Email Domains .......................................20 Appendix C. Acknowledgements .....................................20 Allman, et al. Standards Track [Page 2] RFC 5617 ADSP August 2009 1. Introduction DomainKeys Identified Mail (DKIM) defines a mechanism by which email messages can be cryptographically signed, permitting a signing domain to claim responsibility for the introduction of a message into the mail stream. Message recipients can verify the signature by querying the Signer's domain directly to retrieve the appropriate public key, and thereby confirm that the message was attested to by a party in possession of the private key for the signing domain. However, the legacy of the Internet is such that not all messages will be signed, and the absence of a signature on a message is not an a priori indication of forgery. In fact, during early phases of deployment, it is very likely that most messages will remain unsigned. However, some domains might decide to sign all of their outgoing mail, for example, to protect their brand names. It might be desirable for such domains to be able to advertise that fact to other hosts. This is the topic of Author Domain Signing Practices (ADSP). Hosts implementing this specification can inquire what Author Domain Signing Practices a domain advertises. This inquiry is called an Author Domain Signing Practices check. The basic requirements for ADSP are given in [RFC5016]. This document refers extensively to [RFC4871] and assumes the reader is familiar with it. Requirements Notation: The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 2. Language and Terminology 2.1. Terms Imported from the DKIM Signatures Specification Some terminology used herein is derived directly from [RFC4871]. In several cases, references in that document to "Sender" have been changed to "Author" here, to emphasize the relationship to the Author address(es) in the From: header field described in [RFC5322]. Briefly, o A "Signer" is the agent that signs a message, as defined in Section 2.1 of [RFC4871]. Allman, et al. Standards Track [Page 3] RFC 5617 ADSP August 2009 o A "Local-part" is the part of an address preceding the @ character, as defined in [RFC5322] and used in [RFC4871]. 2.2. Valid Signature A "Valid Signature" is any signature on a message that correctly verifies using the procedure described in Section 6.1 of [RFC4871]. 2.3. Author Address An "Author Address" is an email address in the From: header field of a message [RFC5322]. If the From: header field contains multiple addresses, the message has multiple Author Addresses. 2.4. Author Domain An "Author Domain" is everything to the right of the "@" in an Author Address (excluding the "@" itself). 2.5. Alleged Author An "Alleged Author" is an Author Address of a message; it is "alleged" because it has not yet been checked. 2.6. Author Domain Signing Practices "Author Domain Signing Practices" (or just "practices") consist of a machine-readable record published by the domain of an Alleged Author that includes statements about the domain's practices with respect to mail it sends with its domain in the From: line. 2.7. Author Domain Signature An "Author Domain Signature" is a Valid Signature in which the domain name of the DKIM signing entity, i.e., the d= tag in the DKIM- Signature header field, is the same as the domain name in the Author Address. Following [RFC5321], domain name comparisons are case insensitive. For example, if the From: line address is bob@domain.example, and the message has a Valid Signature with the DKIM-Signature header field containing "d=domain.example", then the message has an Author Domain Signature. Allman, et al. Standards Track [Page 4] RFC 5617 ADSP August 2009 3. Operation Overview Domain owners publish ADSP information via a query mechanism such as the Domain Name System; specific details are given in Section 4.1. Hosts can look up the ADSP information of the domain(s) specified by the Author Address(es) as described in Section 4.3. If a message has multiple Author Addresses, the ADSP lookups SHOULD be performed independently on each address. This document does not address the process a host might use to combine the lookup results. 3.1. ADSP Applicability ADSP as defined in this document is bound to DNS. For this reason, ADSP is applicable only to Author Domains with appropriate DNS records (i.e., A, AAAA, and/or MX) indicating the possible use of the domain for email. The handling of other Author Domains is outside the scope of this document. However, attackers may use such domain names in a deliberate attempt to sidestep an organization's ADSP policy statements. It is up to the ADSP checker implementation to return an appropriate error result for Author Domains outside the scope of ADSP. ADSP applies to specific domains, not domain subtrees. If, for example, an Author Address were user@domain.example, the Author Domain would be domain.example, and the applicable ADSP record would be at _adsp._domainkey.domain.example. An Author Address in a subdomain such as user@sub.domain.example would have a different ADSP record at _adsp._domainkey.sub.domain.example. ADSP makes no connection between a domain and its parent or child domains. Note: If an organization wants to publish Author Domain Signing Practices for all the subdomains it uses, such as host names of servers within the domain, it does so by creating ADSP records for every _adsp._domainkey..domain.example. Wildcards cannot be used (see Section 6.3.); however, suitable DNS management tools could automate creation of the ADSP records. Note: The results from DNS queries that are intended to validate a domain name unavoidably approximate the set of Author Domains that can appear in legitimate email. For example, a DNS A record could belong to a device that does not even have an email implementation. It is up to the checker to decide what degree of approximation is acceptable. Allman, et al. Standards Track [Page 5] RFC 5617 ADSP August 2009 3.2. ADSP Usage Depending on the Author Domain(s) and the signatures in a message, a recipient gets varying amounts of useful information from each ADSP lookup. o If a message has no Valid Signature, the ADSP result is directly relevant to the message. o If a message has an Author Domain Signature, ADSP provides no benefit relative to that domain since the message is already known to be compliant with any possible ADSP for that domain. o If a message has a Valid Signature other than an Author Domain Signature, the receiver can use both the Signature and the ADSP result in its evaluation of the message. 3.3. ADSP Results An ADSP lookup for an Author Address produces one of four possible results: o Messages from this domain might or might not have an Author Domain Signature. This is the default if the domain exists in the DNS but no ADSP record is found. o All messages from this domain are signed with an Author Domain Signature. o All messages from this domain are signed with an Author Domain Signature and are discardable, i.e., if a message arrives without a valid Author Domain Signature, the domain encourages the recipient(s) to discard it. o This domain is out of scope, i.e., the domain does not exist in the DNS. An ADSP lookup could terminate without producing any result if a DNS lookup results in a temporary failure. Allman, et al. Standards Track [Page 6] RFC 5617 ADSP August 2009 4. Detailed Description 4.1. DNS Representation ADSP records are published using the DNS TXT resource record type. The RDATA for ADSP resource records is textual in format, with specific syntax and semantics relating to their role in describing ADSP. The "Tag=Value List" syntax described in Section 3.2 of [RFC4871] is used, modified to use whitespace (WSP) rather than folding whitespace (FWS). Records not in compliance with that syntax or the syntax of individual tags described in Section 4.3 MUST be ignored (considered equivalent to a NODATA result) for purposes of ADSP, although they MAY cause the logging of warning messages via an appropriate system logging mechanism. If the RDATA contains multiple character strings, the strings are logically concatenated with no delimiters between the strings. Note: ADSP changes the "Tag=Value List" syntax from [RFC4871] to use WSP rather than FWS in its DNS records. Domains MUST NOT publish ADSP records with wildcard names. Wildcards within a domain publishing ADSP records pose a particular problem, as discussed in more detail in Section 6.3. 4.2. Publication of ADSP Records ADSP is intended to apply to all mail sent using the domain name string of an Alleged Author. 4.2.1. Record Syntax ADSP records use the "tag=value" syntax described in Section 3.2 of [RFC4871], modified to use WSP rather than FWS. Every ADSP record MUST start with an outbound signing-practices tag, so the first four characters of the record are lowercase "dkim", followed by optional whitespace and "=". Tags used in ADSP records are described below. Unrecognized tags MUST be ignored. In the ABNF below, the WSP token is imported from [RFC5234]. dkim= Outbound Signing Practices for the domain (plain-text; REQUIRED). Possible values are as follows: unknown The domain might sign some or all email. Allman, et al. Standards Track [Page 7] RFC 5617 ADSP August 2009 all All mail from the domain is signed with an Author Domain Signature. discardable All mail from the domain is signed with an Author Domain Signature. Furthermore, if a message arrives without a valid Author Domain Signature due to modification in transit, submission via a path without access to a signing key, or any other reason, the domain encourages the recipient(s) to discard it. Any other values are treated as "unknown". ABNF: ; Copyright (c) 2009 IETF Trust and the persons identified as ; authors of the code. All rights reserved. ; Redistribution and use in source and binary forms, with or without ; modification, are permitted provided that the following conditions ; are met: ; - Redistributions of source code must retain the above copyright ; notice, this list of conditions and the following disclaimer. ; - Redistributions in binary form must reproduce the above copyright ; notice, this list of conditions and the following disclaimer in ; the documentation and/or other materials provided with the ; distribution. ; - Neither the name of Internet Society, IETF or IETF Trust, nor the ; names of specific contributors, may be used to endorse or promote ; products derived from this software without specific prior ; written permission. ; THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ; 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT ; LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS ; FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE ; COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, ; INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ; (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ; SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) ; HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN ; CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR ; OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, ; EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Allman, et al. Standards Track [Page 8] RFC 5617 ADSP August 2009 adsp-dkim-tag = %x64.6b.69.6d *WSP "=" *WSP ("unknown" / "all" / "discardable" / x-adsp-dkim-tag) x-adsp-dkim-tag = hyphenated-word ; for future extension ; hyphenated-word is defined in RFC 4871 4.3. ADSP Lookup Procedure Hosts doing an ADSP lookup MUST produce a result that is semantically equivalent to applying the following steps in the order listed below. In practice, these steps can be performed in parallel in order to improve performance. However, implementations SHOULD avoid doing unnecessary DNS lookups. For the purposes of this section, a "valid ADSP record" is one that is both syntactically and semantically correct; in particular, it matches the ABNF for a "tag-list" and starts with a valid "dkim" tag. Check Domain Scope: An ADSP checker implementation MUST determine whether a given Author Domain is within the scope for ADSP. Given the background in Section 3.1, the checker MUST decide which degree of approximation is acceptable. The checker MUST return an appropriate error result for Author Domains that are outside the scope of ADSP. The host MUST perform a DNS query for a record corresponding to the Author Domain (with no prefix). The type of the query can be of any type, since this step is only to determine if the domain itself exists in DNS. This query MAY be done in parallel with the query to fetch the named ADSP Record. If the result of this query is that the Author Domain does not exist in the DNS (often called an NXDOMAIN error, rcode=3 in [RFC1035]), the algorithm MUST terminate with an error indicating that the domain is out of scope. Note that a result with rcode=0 but no records (often called NODATA) is not the same as NXDOMAIN. NON-NORMATIVE DISCUSSION: Any resource record type could be used for this query since the existence of a resource record of any type will prevent an NXDOMAIN error. MX is a reasonable choice for this purpose because this record type is thought to be the most common for domains used in email, and will therefore produce a result that can be more readily cached than a negative result. If the domain does exist, the checker MAY make more extensive checks to verify the existence of the domain, such as the ones described in Section 5 of [RFC5321]. If those checks indicate Allman, et al. Standards Track [Page 9] RFC 5617 ADSP August 2009 that the Author Domain does not exist for mail, e.g., the domain has no MX, A, or AAAA record, the checker SHOULD terminate with an error indicating that the domain is out of scope. Fetch Named ADSP Record: The host MUST query DNS for a TXT record corresponding to the Author Domain prefixed by "_adsp._domainkey." (note the trailing dot). If the result of this query is a NOERROR response (rcode=0 in [RFC1035]) with an answer that is a single record that is a valid ADSP record, use that record, and the algorithm terminates. If the result of the query is NXDOMAIN or NOERROR with zero records, there is no ADSP record. If the result of the query contains more than one record, or a record that is not a valid ADSP record, the ADSP result is undefined. If a query results in a "SERVFAIL" error response (rcode=2 in [RFC1035]), the algorithm terminates without returning a result; possible actions include queuing the message or returning an SMTP error indicating a temporary failure. See Appendix A for examples of ADSP lookup. 5. IANA Considerations ADSP adds the following namespaces to the IANA registry. In all cases, new values are assigned only for values that have been documented in a published RFC after IETF Review, as specified in [RFC5226]. 5.1. ADSP Specification Tag Registry An ADSP record provides for a list of specification tags. IANA has established the ADSP Specification Tag Registry for specification tags that can be used in ADSP fields. The initial entry in the registry is: +------+-----------------+ | TYPE | REFERENCE | +------+-----------------+ | dkim | (RFC 5617) | +------+-----------------+ ADSP Specification Tag Registry Initial Values Allman, et al. Standards Track [Page 10] RFC 5617 ADSP August 2009 5.2. ADSP Outbound Signing Practices Registry The "dkim=" tag specification, defined in Section 4.2.1, provides for a value specifying Outbound Signing Practices. IANA has established the ADSP Outbound Signing Practices Registry for Outbound Signing Practices. The initial entries in the registry comprise: +-------------+-----------------+ | TYPE | REFERENCE | +-------------+-----------------+ | unknown | (RFC 5617) | | all | (RFC 5617) | | discardable | (RFC 5617) | +-------------+-----------------+ ADSP Outbound Signing Practices Registry Initial Values 5.3. Authentication-Results Method Registry Update IANA has added the following to the Email Authentication Method Name Registry: Method: dkim-adsp Defined In: RFC 5617 ptype: header property: from value: contents of the [RFC5322] From: header field, with comments removed 5.4. Authentication-Results Result Registry Update IANA has added the following in the Email Authentication Result Name Registry: Code: none Existing/New Code: existing Defined In: [RFC5451] Auth Method: dkim-adsp (added) Allman, et al. Standards Track [Page 11] RFC 5617 ADSP August 2009 Meaning: No DKIM Author Domain Signing Practices (ADSP) record was published. Code: pass Existing/New Code: existing Defined In: [RFC5451] Auth Method: dkim-adsp (added) Meaning: This message had an Author Domain Signature that was validated. (An ADSP check is not strictly required to be performed for this result since a valid Author Domain Signature satisfies all possible ADSP policies.) Code: unknown Existing/New Code: new Defined In: RFC 5617 Auth Method: dkim-adsp Meaning: No valid Author Domain Signature was found on the message and the published ADSP was "unknown". Code: fail Existing/New Code: existing Defined In: [RFC5451] Auth Method: dkim-adsp (added) Meaning: No valid Author Domain Signature was found on the message and the published ADSP was "all". Code: discard Existing/New Code: new Defined In: RFC 5617 Auth Method: dkim-adsp Meaning: No valid Author Domain Signature was found on the message and the published ADSP was "discardable". Allman, et al. Standards Track [Page 12] RFC 5617 ADSP August 2009 Code: nxdomain Existing/New Code: new Defined In: RFC 5617 Auth Method: dkim-adsp Meaning: Evaluating the ADSP for the Author's DNS domain indicated that the Author's DNS domain does not exist. Code: temperror Existing/New Code: existing Defined In: [RFC5451] Auth Method: dkim-adsp (added) Meaning: An ADSP record could not be retrieved due to some error that is likely transient in nature, such as a temporary DNS error. A later attempt may produce a final result. Code: permerror Existing/New Code: existing Defined In: [RFC5451] Auth Method: dkim-adsp (added) Meaning: An ADSP record could not be retrieved due to some error that is likely not transient in nature, such as a permanent DNS error. A later attempt is unlikely to produce a final result. 6. Security Considerations Security considerations in the ADSP are mostly related to attempts on the part of malicious senders to represent themselves as Authors for whom they are not authorized to send mail, often in an attempt to defraud either the recipient or an Alleged Author. Additional security considerations regarding Author Domain Signing Practices are found in the DKIM threat analysis [RFC4686]. Allman, et al. Standards Track [Page 13] RFC 5617 ADSP August 2009 6.1. ADSP Threat Model Email recipients often have a core set of content Authors that they already trust. Common examples include financial institutions with which they have an existing relationship and Internet web transaction sites with which they conduct business. Email abuse often seeks to exploit a legitimate email Author's name- recognition among recipients by using the Author's domain name in the From: header field. Especially since many popular Mail User Agents (MUAs) do not display the Author's email address, there is no empirical evidence of the extent that this particular unauthorized use of a domain name contributes to recipient deception or that eliminating it will have significant effect. However, closing this potential exploit could facilitate some types of optimized processing by receive-side message filtering engines, since it could permit them to maintain higher-confidence assertions about From: header field uses of a domain when the occurrence is authorized. Unauthorized uses of domain names occur elsewhere in messages, as do unauthorized uses of organizations' names. These attacks are outside the scope of this specification. ADSP does not provide any benefit -- nor, indeed, have any effect at all -- unless an external system acts upon the verdict, either by treating the message differently during the delivery process or by showing some indicator to the end recipient. Such a system is out of scope for this specification. ADSP checkers may perform multiple DNS lookups per Alleged Author Domain. Since these lookups are driven by domain names in email message headers of possibly fraudulent email, legitimate ADSP checkers can become participants in traffic multiplication attacks on domains that appear in fraudulent email. 6.2. DNS Considerations An attacker might attack the DNS infrastructure in an attempt to impersonate ADSP records to influence a receiver's decision on how it will handle mail. However, such an attacker is more likely to attack at a higher level, e.g., redirecting A or MX record lookups in order to capture traffic that was legitimately intended for the target domain. These DNS security issues are addressed by DNSSEC [RFC4033]. Allman, et al. Standards Track [Page 14] RFC 5617 ADSP August 2009 Because ADSP operates within the framework of the legacy email system, the default result in the absence of an ADSP record is that the domain does not sign all of its messages. It is therefore important that the ADSP clients distinguish a DNS failure such as "SERVFAIL" from other DNS errors so that appropriate actions can be taken. 6.3. DNS Wildcards DNS wildcards (described in [RFC4592]) that exist in the DNS hierarchy at or above the domain being checked interfere with the ability to verify the scope of the ADSP check described in Section 4.3. For example, a wildcard record for *.domain.example makes all subdomains such as foo.domain.example exist in the DNS. Domains that intend to make active use of ADSP by publishing a practice other than unknown are advised to avoid the use of wildcards in their hierarchy. If a domain contains wildcards, then any name that matches the wildcard can appear to be a valid mail domain eligible for ADSP. But the "_adsp._domainkey." prefix on ADSP records does not allow publication of wildcard records that cover ADSP records without also covering non-ADSP records, nor does it allow publication of wildcard records that cover non-ADSP records without also covering ADSP records. A domain that uses ADSP practices other than unknown SHOULD NOT publish wildcard records. 6.4. Inappropriate Application of Author Domain Signatures In one model of DKIM usage, a domain signs messages that are in transit through their system. Since any signature whose domain matches the Author Domain is, by definition, an Author Domain Signature, it would be unwise to sign mail whose Author Domain is the Signer's domain if the mail is not known to meet the domain's standards for an Author Domain Signature. One such use case is where a domain might apply such a signature following application of an Authentication-Results header field as described in Section 7.1 of [RFC5451]. This problem can be easily avoided either by not applying a signature that might be confused with an Author Domain Signature or by applying a signature from some other domain, such as a subdomain of the Author Domain. Allman, et al. Standards Track [Page 15] RFC 5617 ADSP August 2009 7. References 7.1. Normative References [RFC1035] Mockapetris, P., "Domain names - implementation and specification", STD 13, RFC 1035, November 1987. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC4033] Arends, R., Austein, R., Larson, M., Massey, D., and S. Rose, "DNS Security Introduction and Requirements", RFC 4033, March 2005. [RFC4592] Lewis, E., "The Role of Wildcards in the Domain Name System", RFC 4592, July 2006. [RFC4871] Allman, E., Callas, J., Delany, M., Libbey, M., Fenton, J., and M. Thomas, "DomainKeys Identified Mail (DKIM) Signatures", RFC 4871, May 2007. [RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 5226, May 2008. [RFC5234] Crocker, D. and P. Overell, "Augmented BNF for Syntax Specifications: ABNF", STD 68, RFC 5234, January 2008. [RFC5322] Resnick, P., Ed., "Internet Message Format", RFC 5322, October 2008. [RFC5451] Kucherawy, M., "Message Header Field for Indicating Message Authentication Status", RFC 5451, April 2009. 7.2. Informative References [RFC4686] Fenton, J., "Analysis of Threats Motivating DomainKeys Identified Mail (DKIM)", RFC 4686, September 2006. [RFC5016] Thomas, M., "Requirements for a DomainKeys Identified Mail (DKIM) Signing Practices Protocol", RFC 5016, October 2007. [RFC5321] Klensin, J., "Simple Mail Transfer Protocol", RFC 5321, October 2008. Allman, et al. Standards Track [Page 16] RFC 5617 ADSP August 2009 Appendix A. Lookup Examples Assume the example domain publishes these DNS records (in these examples, the numbers in parentheses are comments to help identify the records, not part of the records themselves): aaa.example A 192.0.2.1 (1) _adsp._domainkey.aaa.example TXT "dkim=all" (2) bbb.example MX 10 mail.bbb.example (3) mail.bbb.example A 192.0.2.2 (4) A.1. Domain and ADSP Exist A mail message contains this From: header line: From: bob@aaa.example (Bob the Author) The ADSP lookup first identifies the Author Address bob@aaa.example and the Author Domain aaa.example. It does an MX DNS query for aaa.example and gets back a NOERROR result with no DNS records. (There's no MX record, but since record (1) exists, the name exists in the DNS.) Since that query didn't return an error, the lookup proceeds to a TXT DNS query for _adsp._domainkey.aaa.example, which returns record (2). Since this is a valid ADSP record, the result is that all messages from this domain are signed. A.2. Domain Exists, ADSP Does Not Exist A mail message contains this From: header line: From: alice@bbb.example (Old-fashioned Alice) The ADSP lookup first identifies the Author Address alice@bbb.example and the Author Domain bbb.example. It does an MX DNS query for bbb.example and gets back record (3). Since that query didn't return an error, it then proceeds to a TXT DNS query for _adsp._domainkey.bbb.example, which returns NXDOMAIN. Since the domain exists but there is no ADSP record, ADSP returns the default unknown result: messages may or may not have an author domain signature. A.3. Domain Does Not Exist A mail message contains this From: header line: From: frank@ccc.example (Unreliable Frank) Allman, et al. Standards Track [Page 17] RFC 5617 ADSP August 2009 The ADSP lookup first identifies the Author Address frank@ccc.example and the Author Domain ccc.example. It does an MX DNS query for ccc.example and gets back an NXDOMAIN result since there are no records at all for ccc.example. The lookup terminates with the result that the domain does not exist in the DNS and so is out of scope. Appendix B. Usage Examples These examples are intended to illustrate typical uses of ADSP. They are not intended to be exhaustive or to apply to every domain's or mail system's individual situation. Domain managers are advised to consider the ways that mail processing can modify messages in ways that will invalidate an existing DKIM signature, such as mailing lists, courtesy forwarders, and other paths that could add or modify headers, or modify the message body. If the modifications invalidate the DKIM signature, recipient hosts will consider the mail not to have an Author Domain Signature, even though the signature was present when the mail was originally sent. B.1. Single Location Domains One common mail system configuration handles all of a domain's users' incoming and outgoing mail through a single Mail Transport Agent (MTA) or group of MTAs. With this configuration, the MTA(s) can be configured to sign outgoing mail with an Author Domain Signature. In this situation, it might be appropriate to publish an ADSP record for the domain containing "all", depending on whether the users also send mail through other paths that do not apply an Author Domain Signature. Such paths could include MTAs at hotels or hotspot networks used by travelling users, web sites that provide "mail an article" features, user messages sent through mailing lists, or third-party mail clients that support multiple user identities. B.2. Bulk Mailing Domains Another common configuration uses a domain solely for bulk or broadcast mail, with no individual human users -- again, typically sending all the mail through a single MTA or group of MTAs that can apply an Author Domain Signature. In this case, the domain's management can be confident that all of its outgoing mail will be sent through the signing MTA(s). Lacking individual users, the domain is unlikely to participate in mailing lists, but could still send mail through other paths that might invalidate signatures. Allman, et al. Standards Track [Page 18] RFC 5617 ADSP August 2009 Domain owners often use specialist mailing providers to send their bulk mail. In this case, the mailing provider needs access to a suitable signing key in order to apply an Author Domain Signature. One possible route would be for the domain owner to generate the key and give it to the mailing provider. Another would be for the domain to delegate a subdomain to the mailing provider, for example, bigbank.example might delegate email.bigbank.example to such a provider; in this case, the provider can generate the keys and DKIM DNS records itself and use the subdomain in the Author Address in the mail. Regardless of the DNS and key management strategy chosen, whoever maintains the DKIM records for the domain could also install an ADSP record containing "all". B.3. Bulk Mailing Domains with Discardable Mail In some cases, a domain might sign all of its outgoing mail with an Author Domain Signature and prefer that recipient systems discard mail without a valid Author Domain Signature in order to avoid having its mail confused with mail sent from sources that do not apply an Author Domain Signature. (In the case of domains with tightly controlled outgoing mail, this latter kind of mail is sometimes loosely called "forgeries".) In such cases, it might be appropriate to publish an ADSP record containing "discardable". Note that a domain SHOULD NOT publish a "discardable" record if it wishes to maximize the likelihood that mail from the domain is delivered, since it could cause some fraction of the mail the domain sends to be discarded. B.4. Third-Party Senders Another common use case is for a third party to enter into an agreement whereby that third party will send bulk or other mail on behalf of a designated Author or Author Domain, using that domain in the [RFC5322] From: or other headers. Due to the many and varied complexities of such agreements, third-party signing is not addressed in this specification. B.5. Domains with Independent Users and Liberal Use Policies When a domain has independent users and its usage policy does not explicitly restrict them to sending mail only from designated mail servers (e.g., many ISP domains and even some corporate domains), then it is only appropriate to publish an ADSP record containing "unknown". Publishing either "all" or "discardable" will likely result in significant breakage because independent users are likely to send mail from the external paths enumerated in Appendix B.1. Allman, et al. Standards Track [Page 19] RFC 5617 ADSP August 2009 B.6. Non-Email Domains If a domain sends no mail at all, it can safely publish a "discardable" ADSP record, since any mail with an Author Address in the domain is a forgery. Appendix C. Acknowledgements This document greatly benefited from comments by Steve Atkins, Jon Callas, Dave Crocker, Pasi Eronen, JD Falk, Arvel Hathcock, Ellen Siegel, Michael Thomas, and Wietse Venema. Allman, et al. Standards Track [Page 20] RFC 5617 ADSP August 2009 Authors' Addresses Eric Allman Sendmail, Inc. 6475 Christie Ave, Suite 350 Emeryville, CA 94608 Phone: +1 510 594 5501 EMail: eric+dkim@sendmail.org Jim Fenton Cisco Systems, Inc. 170 W. Tasman Drive San Jose, CA 95134-1706 Phone: +1 408 526 5914 EMail: fenton@cisco.com Mark Delany Yahoo! Inc. 701 First Avenue Sunnyvale, CA 94089 Phone: +1 408 349 6831 EMail: markd+dkim@yahoo-inc.com John Levine Taughannock Networks PO Box 727 Trumansburg, NY 14886 Phone: +1 831 480 2300 EMail: standards@taugh.com URI: http://www.taugh.com Allman, et al. Standards Track [Page 21]